Victron Energy

  The Argo Battery Combiners feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. Brand Victron Energy Manufacturer Part Number BCD000402000 Maximum Continuous Current (A) 40 Number Of Batteries 2 Connection M6 Bolts Dimensions H60 x W120 x D75mm Weight (kg) 0.8 Warranty 5 Years

Read more less

The BatteryProtect is not designed for reverse currents from charging sources. Features 12/24V auto ranging The BatteryProtect automatically detects system voltage. Programming made easy The BatteryProtect can be set to engage / disengage at several different voltages. The seven segment display will indicate which setting has been chosen. A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Ultra low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information. Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V. Ignition proof No relays but MOSFET switches, and therefore no sparks. Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage. Brand Victron Energy Manufacturer Part Number BPR000065400 Voltage 12/24 Peak Current (During 30 Seconds) 250A Max. Continuous Load Current 65A Connection M6 IP Rating Electronics: IP67 (potted) Connections: IP00 Dimensions (Including Terminals) H40 x W48 x D106mm Weight (kg) 0.2 Warranty 5 Years

Read more less

Liquid crystal display For status monitoring and set-up Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A Brand Victron Energy Manufacturer Part Number SCC040030050 GTIN 8719076046257 Battery Voltage 48V Rated Charge Current 30A Maximum Solar Voltage 100V Load Output Manual control + low voltage disconnect + timer Grounding Common positive IP Rating IP20 Dimensions H101 x W184 x D47mm Weight 0.3Kg Warranty 5 Years

Read more less

High stock levels available on all panels, please contact us via live chat for up-to-date stock before purchase, as stock levels are subject to change. Alternatively, you can email or call us. Sealed, waterproof, multi-functional junction box gives high level of safety. High performance bypass diodes minimize the power drop caused by shade. Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation. A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems. Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance. High power models with pre-wired quick-connect system with MC4 (PV-ST01) connectors. Brand Victron Energy Manufacturer Part Number SPM040401200 Voltage 12 Nominal Power (W) 40 Number of cells in series 36 Maximun System Voltage 1000 Dimensions L425 x W668 x D25mm Weight (kg) 3.1 Warranty 5 Years Cell Type Monocrystalline

Read more less

Completely encapsulated: waterproof, shockproof and ignition protected Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.   Extra-long input and output cables Thanks to the cables of 1.8 meters in length, intermediate cable interconnections to increase length even more will in most cases not be needed. This is an important reliability increasing feature in an area were IP67 protection grade is needed.   Wide input voltage range With 15 to 40 Volts input range, a stable output is ensured during surges or sags due to other equipment connected to same battery.   Protected against overheating It can be used in a hot environment such as a machine room. Brand Victron Energy Manufacturer Part Number ORI241220260 GTIN 8719076048442 Voltage 24/12V Cont. Output Current 20A Efficiency 95% Protection Category IP67 Bluetooth Enabled No Dimensions H74 x W74 x D32mm Weight 0.3Kg Warranty 5 Years Country of Manufacture China

Read more less

Brand Victron Energy Manufacturer Part Number ASS000100000 Warranty 5 Years

Read more less

It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws. Brand Victron Energy Manufacturer Part Number SCC950400300 Warranty 5 Years

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.   Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual.   Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.   Programming, real-time data and history display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed. Brand Victron Energy Manufacturer Part Number SCC010010050R GTIN 8719076025306 Battery Voltage 12/24V Auto Select Rated Charge Current 10A Nominal PV Power, 12V 145W Nominal PV Power, 24V 290W Max. PV Short Circuit Current 10A Maximum PV Open Circuit Voltage 75V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D40mm Weight 0.5Kg Warranty 5 Years

Read more less

Features Lighting control function, fully programmable. Three stage battery charging (bulk, absorption, float), fully programmable. Integrated battery monitor function (Remote Panel needed to display state of charge). Load output with low voltage disconnect and manual control (default setting). Optional external temperature sensor. – Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options See Remote Panel manual for details Brand Victron Energy Manufacturer Part Number SCC010020110 GTIN 8719076025382 Battery Voltage 12/24V with automatic system voltage detection Rated Charge Current 20A Maximum Solar Voltage 28V / 55V Load Output Manual control + low voltage disconnect + timer Grounding Common positive IP Rating IP30 Dimensions H160 x W82 x D48mm Weight 0.3Kg Warranty 5 Years

Read more less

High stock levels available on all panels, please contact us via live chat for up-to-date stock before purchase, as stock levels are subject to change. Alternatively, you can email or call us. Sealed, waterproof, multi-functional junction box gives high level of safety. High performance bypass diodes minimize the power drop caused by shade. Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation. A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems. Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance. High power models with pre-wired quick-connect system with MC4 (PV-ST01) Brand Victron Energy Manufacturer Part Number SPP040451200 Voltage 12 Nominal Power (W) 45 Number of cells in series 36 Maximun System Voltage 1000 Dimensions L425 x W668 x D25mm Weight (kg) 3.1 Warranty 5 Years Cell Type Polycrystalline

Read more less

Solar Home System 200 MPPT not included   Brand Victron Energy Manufacturer Part Number SHS800300300 gtin 8719076055389 Dimensions L364 x W207 x H310mm Weight 0.4Kg Warranty 5 Years Country of Manufacture India

Read more less

 Features Load output with low battery voltage disconnect function. Lighting control function, one timer only.  Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.  Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC040010020 GTIN 8719076025573 Battery Voltage 48V Rated Charge Current 10A Maximum Solar Voltage 100V IP Rating IP20 Dimensions H95 x W140 x D33.5mm Weight 0.17Kg Warranty 5 Years  

Read more less

  Brand Victron Energy Manufacturer Part Number SCC010020060 GTIN 8719076046219 Battery Voltage 12/24 V with automatic system voltage detection [for LiFePO4 no automatic system voltage detection] Rated Charge Current 20A Second battery output Yes Load Output 2 USB ports 5V/2A Grounding Common negative Battery Temperature Sensor Yes, remote sensor [included] Protection Category IP20 Dimensions H101.5 x W184.0 x D47.1mm Weight 0.3Kg Warranty 5 Years

Read more less

To measure the power and energy of the whole application at the distribution box. Or to measure the output of a PV Inverter, to display the data on the Color Control GX and the VRM Portal. The Energy Meter can be used for four things: Grid meter, and used as control input for an ESS System (1). Measure the output of a PV Inverter Measure the output of a AC Genset The meter is connected to the Color Control GX. There are two options in its wiring: Direct connection, either using the RS485 to USB interface with 1.8m cable length, or the 5.0m cable. Wireless connection via Zigbee Brand Victron Energy Manufacturer Part Number REL300100000 Warranty 5 Years

Read more less

It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws. Brand Victron Energy Manufacturer Part Number SCC950300210 Warranty 5 Years

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Programming, real-time data and history display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed. Brand Victron Energy Manufacturer Part Number SCC010015050R GTIN 8719076025320 Battery Voltage 12/24V Auto Select Rated Charge Current 15A Nominal PV Power, 12V 220W Nominal PV Power, 24V 440W Max. PV Short Circuit Current 15A Maximum PV Open Circuit Voltage 75V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D40mm Weight 0.5Kg Warranty 5 Years

Read more less

To easily mount the MPPT Control on a wall, instead of flush mounted in a panel, use one of our wall mount enclosures. See the related products slider below.  Features  View live status information, including solar watts, battery voltage, charge current, load current and more.  View historical information    A. All-time values    B. 30-day historical values MPPT setup Brand Victron Energy Manufacturer Part Number SCC900500000 Power Supply Voltage Range 6.5-95 V DC Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number CIP100400070 Warranty 5 Years Country of Manufacture Slovenia    

Read more less

  Brand Victron Energy Manufacturer Part Number VBS127010010 GTIN 8719076052258 Max. Continuous Current 275A One Minute Rating 455A Cranking Rating 1250A Voltage Rating 48V Terminal Material Tin-plated copper Hex Nut Material Tin-plated copper Terminal Diameter 3/8 inch / 9.53mm Recommended Torque 70 lbf·inch / 8 N·m Base Material Glass fiber reinforced nylon Mounting Surface or rear panel mount Dimensions H69 x W69 x D73mm Weight 0.2Kg Warranty 5 Years Country of Manufacture Taiwan

Read more less

  Brand Victron Energy Manufacturer Part Number ASS030560100 Cable Length 1m Warranty 5 Years

Read more less

Use the AC Current sensor to measure and visualise the solar production of a PV Inverter. The measurements will be visible on the GX device and on the VRM Portal.   The AC Current Sensor is one out of multiple options to visualise the solar yield in a Victron system   Brand Victron Energy Manufacturer Part Number CSE000100000 Warranty 5 Years

Read more less

It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws. Brand Victron Energy Manufacturer Part Number SCC950300300 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number ASS030560200 Cable Length 2m Warranty 5 Years

Read more less

It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws.

Read more less

Features Load output with low battery voltage disconnect function. Lighting control function, one timer only.  Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.  Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details   CLICK HERE FOR SPEC SHEET   Brand Victron Energy Manufacturer Part Number SCC040020020 Warranty 5 Years IP Rating IP20 Weight (kg) 0.17 Dimensions H95 x W140 x D33.5mm Battery Voltage 48V Rated Charge Current 20A Maximum Solar Voltage 100V Grounding Common positive

Read more less

High stock levels available on all panels, please contact us via live chat for up-to-date stock before purchase, as stock levels are subject to change. Alternatively, you can email or call us. Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation. A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems. Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance. High power models with pre-wired quick-connect system with MC4 (PV-ST01) connectors. Brand Victron Energy Manufacturer Part Number SPP040601200 Voltage 12 Nominal Power (W) 60 Number of cells in series 36 Maximun System Voltage 1000 Dimensions L545 x W668 x D25mm Weight (kg) 4 Warranty 5 Years Cell Type Polycrystalline

Read more less

  Brand Victron Energy Manufacturer Part Number ASS030560300 Cable Length 3m Warranty 5 Years

Read more less

Features of the Blue Smart IP65 Charger 6V/12V-1.1 The battery is charged, smartly… to perfect condition The seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance… and a longer life.   Recovery of deeply-discharged ‘dead’ batteries Unlike other brands, the Blue Smart IP65 Charger 6V/12V-1.1will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals.   ReconditioningA lead-acid battery that has been insufficiently charged or has been left discharged during days or weeks will deteriorate due to sulfation. If caught in time, sulfation can sometimes be partially reversed by charging the battery with low current up to a higher voltage.   Connect the battery with ease The charger comes with both crocodile clips and M8 eyelets – making it easy to connect to the battery. If you wish, you can leave it permanently connected.   Brand Victron Energy Manufacturer Part Number BPC120134024R gtin 8719076055532 Voltage 6/12V Charge Current 1.1A Input Voltage 230V Protection Category IP65 Efficiency 82% Bluetooth Enabled Yes Plug Type UK Dimensions H38 x W64 x D153mm Weight 0.4Kg Warranty 5 Years Country of Manufacture India

Read more less

The miniBMS has two outputs, similar to the VE.Bus BMS.  Brand Victron Energy Manufacturer Part Number BMS400100000 Input Voltage Range 8-70VDC Protection Category IP20 Dimensions H106 x W42 x D23mm Weight (kg) 0.1 Warranty 5 Years

Read more less

Outdoor LTE-M Wall-Mount Antenna

Read more less

Brand Victron Energy Manufacturer Part Number ASS030510120 Warranty 5 Years

Read more less

Features LED indicators Green: on (battery voltage > 27,3V) Orange: lower battery leg active (deviation > 0,1V) Orange: upper battery leg active (deviation > 0,1V) Red: alarm (deviation > 0,2V). Remains on until the deviation has reduced to less than 0,14V, or until system voltage drops to less than 26,6V. Alarm relay Normally open. The alarm relay closes when the red LED switches on and opens when the red LED switches off Alarm reset Two terminals are available to connect a push button. Interconnecting the two terminals resets the relay. The reset condition will remain active until the alarm is over. Thereafter the relay will close again when a new alarm occurs Even more insight and control with the midpoint monitoring function of the BMV-702 Battery Monitor The BMV-702 measures the midpoint of a string of cells or batteries. It displays the deviation from the ideal midpoint in volts or percent. Separate deviation percentages can be set to trigger a visual/audible alarm and to close a potential free relay contact for remote alarm purposes. Brand Victron Energy Manufacturer Part Number BBA000100100 Input Voltage Range Up to 18V per battery, 36V total Midpoint deviation to start balancing 50 mV Alarm Relay 60V / 1A normally open Over Temperature Protection Yes Protection Category IP22 Dimensions H100 x W113 x D47mm Weight (kg) 0.4 Warranty 5 Years

Read more less

Liquid crystal display For status monitoring and set-up Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A Brand Victron Energy Manufacturer Part Number SCC040010050 GTIN 8719076046233 Battery Voltage 48V Rated Charge Current 10A Maximum Solar Voltage 100V Load Output Manual control + low voltage disconnect + timer Grounding Common positive IP Rating IP20 Dimensions H101 x W184 x D47mm Weight 0.3Kg Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number BPA000100010R Dimensions L120 x W65 x D3mm Weight (kg) 0.2 Warranty 5 Years  

Read more less

Features VRLA technology VRLA stands for Valve Regulated Lead Acid, which means that the batteries are sealed. Gas will escape through the safety valves only in case of overcharging or cell failure. VRLA batteries are maintenance free for life. Sealed (VRLA) AGM Batteries AGM stands for Absorbent Glass Mat. In these batteries the electrolyte is absorbed into a glass-fibre mat between the plates by capillary action. As explained in our book ‘Energy Unlimited’, AGM batteries are more suitable for short-time delivery of high currents than gel batteries. Low Self-Discharge Because of the use of lead calcium grids and high purity materials, Victron VRLA batteries can be stored during long periods of time without recharge. The rate of self-discharge is less than 2% per month at 20°C. The self-discharge doubles for every increase in temperature by 10°C. Victron VRLA batteries can therefore be stored for up to a year without recharging, if kept under cool conditions. Exceptional Deep Discharge Recovery Victron VRLA batteries have exceptional discharge recovery, even after deep or prolonged discharge. Nevertheless repeatedly deep and prolonged discharge has a very negative effect on the service life of all lead acid batteries, Victron batteries are no exception. Battery Discharging Characteristics The rated capacity of Victron AGM and Gel Deep Cycle batteries refers to 20 hour discharge, in other words: a discharge current of 0,05 C. The rated capacity of Victron Tubular Plate Long Life batteries refers to 10 hours discharge. The effective capacity decreases with increasing discharge current (see table 1). Please note that the capacity reduction will be even faster in case of a constant power load, such as an inverter.  All Prices Include VAT   Brand Victron Energy Manufacturer Part Number BAT212200084 GTIN 8719076036944 Voltage 12V Battery Capacity (C20) 22Ah Terminal Type M8 Terminal Layout Right Hand Positive Dimensions (Including Terminals) L181 x W77 x H167mm Weight 5.8kg Warranty 2 Years Country of Manufacture Vietnam Battery Technology AGM Battery Application Deep Cycle  

Read more less

Cyrix Battery Combiners are an excellent replacement for diode isolators. The main feature is that there is virtually no voltage loss so that the output voltage of alternators or battery chargers does not need to be increased.   Features Intelligent battery monitoring to prevent unwanted switching Some battery combiners (also called voltage controlled relay, or split charge relay) will disconnect a battery in case of a short but high amperage load. A battery combiner also may fail to connect a large but discharged battery bank because the DC voltage immediately drops below the disengage value once the batteries are connected. The software of the Cyrix-ct 12/24 does more than simply connect and disconnect based on battery voltage and with a fixed time delay. The Cyrix-ct 12/24 looks at the general trend (voltage increasing or decreasing) and reverses a previous action only if the trend has reversed during a certain period of time. The time delay depends on the voltage deviation from the trend. (for Battery Combiners with multiple engage/disengage profiles, please see the Cyrix-i 400) Protection against overheating (due to a long duration overload e.g.) The Cyrix will disengage in case of excessive contact temperature, and reengage again after it has cooled down. 12/24 V auto ranging The Cyrix-ct 12/24 automatically detects system voltage. No voltage loss Cyrix battery combiners are an excellent replacement for diode isolators. The main feature is that there is virtually no voltage loss so that the output voltage of alternators or battery chargers does not need to be increased. Prioritising the starter battery In a typical setup the alternator is directly connected to the starter battery. The accessory battery, and possibly also a bow thruster and other batteries are each connected to the starter battery with Cyrix battery combiners. When a Cyrix senses that the starter battery has reached the connect voltage it will engage, to allow for parallel charging of the other batteries. Bidirectional voltage sensing and power supply from both batteries The Cyrix senses the voltage of both connected batteries. It will therefore also engage if for example the accessory battery is being charged by a battery charger. The Cyrix-ct 12/24 has a dual power supply. It will therefore also close if the voltage on one battery is too low to operate the Cyrix. In order to prevent unexpected operation during installation or when one battery has been disconnected, the Cyrix-ct 12/24 will not close if the voltage on one of the two battery connections is lower than 2 V (12 V battery) or 4 V (24 V battery). Parallel connection in case of emergency (Start Assist) The Cyrix can also be engaged with a push button (Cyrix remains engaged during 30 seconds) or a switch to connect batteries in parallel manually. This is especially useful in case of emergency when the starter battery is discharged or damaged. Brand Victron Energy Manufacturer Part Number CYR010120011R Voltage 12/24 Continuous Current 120A Cranking Rating (5 seconds) 180A Start Assist Yes (Cyrix remains engaged during 30 seconds) LED Status Indication No Control Cable Included (Length 1 m) No Protection Category IP54 Dimensions H46 x W46 x D80mm Weight (kg) 0.11 Warranty 5 Years

Read more less

Remote on-off connector The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual). All models with adjustable output can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models with adjustable output can be paralleled to increase output current Up to five units can be connected in parallel. Easy to install Delivery includes four Insulated Fastons Female Crimp 6.3mm (eight Fastons in case of the Orion 24/12-40). Low power models: please see Orion-Tr series  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI122408020 Input Voltage Range 9-18V Output Voltage 24V Under Voltage Shutdown 8V Under Voltage Restart 10V Continuous Output Current 8A DC Connection Faston tabs 6.3mm Remote on-off No Galvanic Isolation No Can be connected in parallel No Protection Category IP20 Dimensions H45 x W90 x D115mm Weight (kg) 0.4 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number VBB125021220 gtin 8719076056393 Max. Current Rating 250A Max. Voltage Rating 70VDC Dimensions H48 x W237 x D70mm Weight 0.35Kg Warranty 5 Years Country of Manufacture Taiwan

Read more less

Brand Victron Energy Manufacturer Part Number SCA001000100 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number ASS030120210 GTIN 8719076019404 Warranty 5 Years

Read more less

High stock levels available on all panels, please contact us via live chat for up-to-date stock before purchase, as stock levels are subject to change. Alternatively, you can email or call us. Sealed, waterproof, multi-functional junction box gives high level of safety. High performance bypass diodes minimize the power drop caused by shade. Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation. A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems. Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance. High power models with pre-wired quick-connect system with MC4 (PV-ST01) connectors. Brand Victron Energy Manufacturer Part Number SPM040551200 Voltage 12 Nominal Power (W) 55 Number of cells in series 36 Maximun System Voltage 1000 Dimensions L545 x W668 x D25mm Weight (kg) 4 Warranty 5 Years Cell Type Monocrystalline

Read more less

All Batteries are Made By Leading Manufacturers The AGM range has very low internal resistance making them particularly suitable for high current discharge applications such as for inverters, thrusters and winches.  VRLA AGM: design life 7-10 years   Features VRLA technology VRLA stands for Valve Regulated Lead Acid, which means that the batteries are sealed. Gas will escape through the safety valves only in case of overcharging or cell failure. VRLA batteries are maintenance free for life. Sealed (VRLA) AGM Batteries AGM stands for Absorbent Glass Mat. In these batteries the electrolyte is absorbed into a glass-fibre mat between the plates by capillary action. As explained in our book ‘Energy Unlimited’, AGM batteries are more suitable for short-time delivery of high currents than gel batteries. Low Self-Discharge Because of the use of lead calcium grids and high purity materials, Victron VRLA batteries can be stored during long periods of time without recharge. The rate of self-discharge is less than 2% per month at 20°C. The self-discharge doubles for every increase in temperature by 10°C. Victron VRLA batteries can therefore be stored for up to a year without recharging, if kept under cool conditions. Exceptional Deep Discharge Recovery Victron VRLA batteries have exceptional discharge recovery, even after deep or prolonged discharge. Nevertheless repeatedly deep and prolonged discharge has a very negative effect on the service life of all lead acid batteries, Victron batteries are no exception. Battery Discharging Characteristics The rated capacity of Victron AGM and Gel Deep Cycle batteries refers to 20 hour discharge, in other words: a discharge current of 0,05 C. The rated capacity of Victron Tubular Plate Long Life batteries refers to 10 hours discharge. The effective capacity decreases with increasing discharge current (see table 1). Please note that the capacity reduction will be even faster in case of a constant power load, such as an inverter.  All Prices Include VAT Click Here For Spec Sheet Brand Victron Energy Voltage 12 Volts Technology AGM Capacity 14 Ah Length 151 mm Width 98 mm Height inc. terms 101 mm Weight 4.1 KG    2 YEAR WARRANTY  

Read more less

Features A truly innovative battery The AGM Super Cycle batteries are the result of recent battery electrochemistry developments. The paste of the positive plates is less sensitive to softening, even in case of repeated 100% discharge of the battery, and new additives to the electrolyte reduce sulfation in case of deep discharge. Exceptional 100% depth of discharge (DoD) performance Tests have shown that the Super Cycle battery does withstand at least three hundred 100% DoD cycles. The tests consist of a daily discharge to 10,8V with I = 0,2C20, followed by approximately two hours rest in discharged condition, and then a recharge with I = 0,2C20. The two hours rest period in discharged condition will damage most batteries within 100 cycles, but not the Super Cycle battery. We recommend the Super Cycle battery for applications where an occasional discharge to 100% DoD, or frequent discharge to 60- 80% DoD is expected. Smaller and lighter An additional advantage of the new chemistry is a slightly smaller size and less weight compared to our standard deep cycle AGM batteries. Low internal resistance The internal resistance is also slightly lower compared to our standard deep cycle AGM batteries Brand Victron Energy Manufacturer Part Number BAT412025081 Voltage 12 Capacity (C20) 25 Terminal Type M5 Insert Terminal Layout RH+ Dimensions (Including Terminals) L181 x W77 x H175mm Weight (kg) 6.5 Warranty 2 Years Battery Technology AGM Battery Application Super Cycle

Read more less

MPPT: Ultra Fast Maximum Power Point Tracking By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing. Remote Monitoring and Control Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally. Load output The intelligent Load output function prevents damage caused by running batteries ‘flat’. You can configure the voltage at which SmartSolar disconnects a load – thereby preventing excessive drain on your batteries. And here’s the clever bit: SmartSolar will attempt a 100% recharge every day. If it can’t – during periods of poor weather – it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards, the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers. Brand Victron Energy Manufacturer Part Number SCC075010060R GTIN 8719076040798 Battery Voltage 12/24 Auto Select Rated Charge Current 10A Nominal PV Power, 12V 145W Nominal PV Power, 24V 290W Max. PV Short Circuit Current 13A Maximum PV Open Circuit Voltage 75V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D40mm Weight 0.5Kg Warranty 5 Years

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Programming, real-time data and history display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed. Brand Victron Energy Manufacturer Part Number SCC010015200R GTIN 8719076025337 Battery Voltage 12/24V Auto Select Rated Charge Current 15A Nominal PV Power, 12V 220W Nominal PV Power, 24V 440W Max. PV Short Circuit Current 15A Maximum PV Open Circuit Voltage 100V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D40mm Weight 0.5Kg Warranty 5 Years

Read more less