Victron Energy

Brand Victron Energy Manufacturer Part Number SHP307700240 GTIN 8719076026150 Warranty 5 Years

Read more less

The Cyrix-Li-Charge will disengage immediately whenever its control input becomes free floating, signalling cell over voltage or cell over temperature. In general a cell over voltage alarm will reset shortly after charging has been stopped. The Cyrix will then reconnect the charger after a delay of 3 seconds. After two attempts to reengage with 3 seconds delay, the delay increases to 10 minutes. Whenever battery voltage is less than 13,5V (resp. 27V or 54V), the Cyrix will disengage with a delay of 1 hour. Note 1: In case of zero discharge current, or a small discharge current, the Cyrix will not disengage shortly after the charger has been switched off and/or disconnected, because battery voltage will remain higher than 13,5V. Note 2: If, after the Cyrix has disengaged, the output of the battery charger immediately increases to 13,7V or more, the Cyrix will re-engage, with 3 seconds delay Brand Victron Energy Manufacturer Part Number CYR020120430 Voltage 24/48 Continuous current & Breaking capacity at 12V or 24V 120A Breaking Capacity at 48V 40A Current Consumption When Open 4 mA Protection Category IP54 Dimensions H46 x W46 x D80mm Weight (kg) 0.11 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number ASS030520200 Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number SCC040030020 Warranty 5 Years IP Rating IP20 Weight (kg) 0.17 Dimensions H95 x W140 x D33.5mm Battery Voltage 48V Rated Charge Current 30A Maximum Solar Voltage 100V Grounding Common positive

Read more less

Victron Chargers  Benefits: The battery is charged, smartly… to perfect condition The seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance… and a longer life. Recovery of deeply-discharged ‘dead’ batteries Unlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals. Connect the battery with ease The charger comes with both crocodile clips and M8 eyelets – making it easy to connect to the battery. If you wish, you can leave it permanently connected. Check the status of your battery remotely The Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app.   Features Water, dust and chemical resistant Seven step smart charge algorithm Recovery of fully discharged ‘dead’ batteries Automatic power supply function Severe cold performance: down to -30°C Several other battery life enhancing features Low power mode to charge smaller batteries Li-ion battery mode Setup and configure, readout of voltage and current by Bluetooth Smart   Brand Victron Energy Manufacturer Part Number BPC120431024R Voltage (V) 12 Charger Amps 4 Efficiency 94% Outputs 1 Plug Type UK IP Rating IP65 Dimensions H45 x W81 x D182mm Weight (kg) 0.9 Warranty 5 Years   CLICK HERE FOR SPEC SHEETS

Read more less

Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Programming, real-time data and history display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed. Brand Victron Energy Manufacturer Part Number SCC110020170R GTIN 8719076049845 Battery Voltage 12/24/48V Rated Charge Current 20A Nominal PV Power, 12V 290W Nominal PV Power, 24V 580W Nominal PV Power, 48V 1160W Max. PV Short Circuit Current 20A Maximum PV Open Circuit Voltage 100V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D60mm Weight 0.65Kg Warranty 5 Years

Read more less

  Brand Victron Energy Manufacturer Part Number SHP301603000 Current Rating (A) 16 Standard IEC 60309, 2p+E Cover Glass filled PA6 Weight (kg) 0.23 Warranty 5 Years

Read more less

MPPT: Ultra Fast Maximum Power Point Tracking By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing. Remote Monitoring and Control Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally. Load output The intelligent Load output function prevents damage caused by running batteries ‘flat’. You can configure the voltage at which SmartSolar disconnects a load – thereby preventing excessive drain on your batteries. And here’s the clever bit: SmartSolar will attempt a 100% recharge every day. If it can’t – during periods of poor weather – it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards, the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers. Brand Victron Energy Manufacturer Part Number SCC110020160R GTIN 8719076043027 Battery Voltage 48V Rated Charge Current 20A Nominal PV Power, 12V 290W Nominal PV Power, 24V 580W Nominal PV Power, 48V 1160W Max. PV Short Circuit Current 20A Maximum PV Open Circuit Voltage 100V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D60mm Weight 0.65Kg Warranty 5 Years

Read more less

The Cyrix-Li-Charge will disengage immediately whenever its control input becomes free floating, signalling cell over voltage or cell over temperature. In general a cell over voltage alarm will reset shortly after charging has been stopped. The Cyrix will then reconnect the charger after a delay of 3 seconds. After two attempts to reengage with 3 seconds delay, the delay increases to 10 minutes. Whenever battery voltage is less than 13,5V (resp. 27V or 54V), the Cyrix will disengage with a delay of 1 hour. Note 1: In case of zero discharge current, or a small discharge current, the Cyrix will not disengage shortly after the charger has been switched off and/or disconnected, because battery voltage will remain higher than 13,5V. Note 2: If, after the Cyrix has disengaged, the output of the battery charger immediately increases to 13,7V or more, the Cyrix will re-engage, with 3 seconds delay Brand Victron Energy Manufacturer Part Number CYR010120430 Voltage 12/24 Continuous current & Breaking capacity at 12V or 24V 120A Current Consumption When Open 4 mA Protection Category IP54 Dimensions H46 x W46 x D80mm Weight (kg) 0.11 Warranty 5 Years

Read more less

The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator.   Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely.   Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG120201020R Maximum Charge Current (A) 120 Maximum Alternator Current (A) 120 Number Of Batteries 2 Alternator Energize Input Yes Connection M8 Studs Compensation diode & Energize connection 6.3mm Faston Dimensions H60 x W120 x D115mm Weight (kg) 0.8 Warranty 5 Years

Read more less

Key Features Product Code: SHU065130050 Monitor battery voltage, current, state of charge, and time remaining Track historical data: deepest discharge, average discharge, charge cycles Waterproof and robust IP65-rated enclosure suitable for all environments Connect via Bluetooth with the VictronConnect app for easy monitoring on your smartphone or tablet Optional VE.Direct to USB interface for USB connectivity Compatible with GX devices for both local and remote monitoring via VRM portal Auxiliary input for second battery or midpoint voltage monitoring Seamless integration with Victron solar chargers and select AC chargers via VE.Smart networking No visual or audible alarm; notifications via VictronConnect app or GX device Versions Available: 300 A, 500 A, 1000 A, 2000 A Why Choose SmartShunt 300A IP65? Batteries play a critical role in storing energy, but without the right tools, it’s impossible to gauge the health and charge levels of your batteries just by looking. The SmartShunt 300A IP65 provides comprehensive monitoring capabilities, ensuring you’re never in the dark about your battery’s status. This advanced monitor helps you avoid common battery issues such as over-charging, deep discharges, and excessive temperature effects, thereby safeguarding your investment and extending battery life. The SmartShunt 300A IP65 is a superior alternative to traditional BMV battery monitors, offering a streamlined setup without the need for extensive wiring or additional hardware. Your mobile device acts as the display, offering a clean and user-friendly interface for accessing all battery parameters. Installation and Use Setting up the SmartShunt 300A IP65 is straightforward. Connect it directly to your battery with a VE.Direct cable, and pair it with the VictronConnect app via Bluetooth. For expanded functionality, integrate it with a GX device to monitor your system locally or through the VRM portal remotely.  

Read more less

Features Lighting control function, fully programmable. Three stage battery charging (bulk, absorption, float), fully programmable. Integrated battery monitor function (Remote Panel needed to display state of charge). Load output with low voltage disconnect and manual control (default setting). Optional external temperature sensor. – Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options See Remote Panel manual for details Brand Victron Energy Manufacturer Part Number SCC010030010 GTIN 8719076025399 Battery Voltage 12/24V with automatic system voltage detection Rated Charge Current 30A Maximum Solar Voltage 28V / 55V Load Output Manual control + low voltage disconnect + timer Grounding Common positive IP Rating IP30 Dimensions H200 x W100 x D57mm Weight 0.5Kg Warranty 5 Years

Read more less

Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and Inverters with a VE.Bus communication port. Brand Victron Energy Manufacturer Part Number ASS030140000 Warranty 5 Years

Read more less

MPPT: Ultra Fast Maximum Power Point Tracking By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing. Remote Monitoring and Control Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally. Load output The intelligent Load output function prevents damage caused by running batteries ‘flat’. You can configure the voltage at which SmartSolar disconnects a load – thereby preventing excessive drain on your batteries. And here’s the clever bit: SmartSolar will attempt a 100% recharge every day. If it can’t – during periods of poor weather – it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards, the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers. Brand Victron Energy Manufacturer Part Number SCC110015060R GTIN 8719076040811 Battery Voltage 12/24 Auto Select Rated Charge Current 15A Nominal PV Power, 12V 220W Nominal PV Power, 24V 440W Max. PV Short Circuit Current 15A Maximum PV Open Circuit Voltage 100V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D50mm Weight 0.6Kg Warranty 5 Years

Read more less

Inverters allow you to power domestic equipment – requiring 230V/120V AC – using ‘leisure’ or ‘automotive’ batteries rated at 12V, 24V or 48V DC. Features VE.Direct communication portThe VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed) Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage 210 – 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load and alarms   Proven reliabilityThe full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up powerNeeded to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO modeWhen in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote on/offA remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector. DC connection with screw terminals No special tools needed for installation.  

Read more less

Brand Victron Energy Manufacturer Part Number ASS030130010 GTIN 8719076019428 Weight 0.06Kg Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number SCC900200000 Weight (kg) 0.2 Warranty 5 Years

Read more less

High stock levels available on all panels, please contact us via live chat for up-to-date stock before purchase, as stock levels are subject to change. Alternatively, you can email or call us. Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation. A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems. Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance. High power models with pre-wired quick-connect system with MC4 (PV-ST01) connectors. Brand Victron Energy Manufacturer Part Number SPP040901200 Voltage 12 Nominal Power (W) 90 Number of cells in series 36 Maximun System Voltage 1000 Dimensions L780 x W668 x D30mm Weight (kg) 6.1 Warranty 5 Years Cell Type Polycrystalline

Read more less

Brand Victron Energy Manufacturer Part Number SHU102050200 Warranty 5 Years

Read more less

High stock levels available on all panels, please contact us via live chat for up-to-date stock before purchase, as stock levels are subject to change. Alternatively, you can email or call us. Sealed, waterproof, multi-functional junction box gives high level of safety. High performance bypass diodes minimize the power drop caused by shade. Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation. A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems. Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance. High power models with pre-wired quick-connect system with MC4 (PV-ST01) connectors. Brand Victron Energy Manufacturer Part Number SPM040901200 Voltage 12 Nominal Power (W) 90 Number of cells in series 36 Maximun System Voltage 1000 Dimensions L780 x W668 x D30mm Weight (kg) 6.1 Warranty 5 Years Cell Type Monocrystalline

Read more less

Brand Victron Energy Manufacturer Part Number SCA002000100 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number SHP301604000 Warranty 5 Years

Read more less

The functionality of the Cyrix-Li-ct is analogous to the Cyrix-ct. The Cyrix will disengage immediately: when its control output becomes free floating, signalling cell over voltage or cell over temperature, and/or when battery voltage drops below 13,2V. Start assist function: a short positive pulse will close the relay during 30 seconds A built-in transient voltage suppressor will limit the voltage spike that may occur when the Cyrix suddenly disengages due to cell overvoltage or over temperature.   Brand Victron Energy Manufacturer Part Number CYR010120412 Voltage 12/24 Continuous current & Breaking capacity at 12V or 24V 120A Current Consumption When Open 4 mA Protection Category IP54 Dimensions H46 x W46 x D80mm Weight (kg) 0.11 Warranty 5 Years

Read more less

When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).  If required, Bluetooth can be disabled. The Smart BatteryProtect is not designed for reverse currents from charging sources.   Features Protects the battery against excessive discharge and can be used as a system on/off switch The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The on/off input can be used as a system on/off switch. 12/24V auto ranging The Smart BatteryProtect automatically detects system voltage one time only. Bluetooth: programming made easy When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled. A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS Ultra-low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information. Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V. Ignition proof No relays but MOSFET switches, and therefore no sparks. Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage. Brand Victron Energy Manufacturer Part Number BPR122022000 Voltage 12/24 Peak Current (During 30 Seconds) 600A Max. Continuous Load Current 200A Connection M8 IP Rating Electronics: IP67 (potted) Connections: IP00 Dimensions (Including Terminals) H62 x 123 x D120 Weight (kg) 0.8 Warranty 5 Years

Read more less

Victron Chargers The Blue Smart IP65 Charger is the new professional battery charger with built-in bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans.  Benefits: The battery is charged, smartly… to perfect condition The seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance… and a longer life. Recovery of deeply-discharged ‘dead’ batteries Unlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals. Connect the battery with ease The charger comes with both crocodile clips and M8 eyelets – making it easy to connect to the battery. If you wish, you can leave it permanently connected. Check the status of your battery remotely The Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app.   Features Water, dust and chemical resistant Seven step smart charge algorithm Recovery of fully discharged ‘dead’ batteries Automatic power supply function Severe cold performance: down to -30°C Several other battery life enhancing features Low power mode to charge smaller batteries Li-ion battery mode Setup and configure, readout of voltage and current by Bluetooth Smart   Brand Victron Energy Manufacturer Part Number BPC120431024R Voltage (V) 12 Charger Amps 5 Efficiency 94% Outputs 1 Plug Type UK IP Rating IP65 Dimensions H45 x W81 x D182mm Weight (kg) 0.9 Warranty 5 Years   CLICK HERE FOR SPEC SHEETS

Read more less

Features VE.Direct communication port The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed) Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage 210 – 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load and alarms Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote on/off A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector. DC connection with screw terminals No special tools needed for installation. Brand Victron Energy Manufacturer Part Number PIN122510400 Voltage 12 VA 250 Peak Power (W) 400 Max Efficiency 87% Plug Type UK IP Rating IP21 Dimensions (Including Terminals) H86 x W165 x D260mm Weight (kg) 2.4 Warranty 5 Years

Read more less

The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted. The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor. Differences compared to BMV712 Battery Monitor No programmable visual and audible alarm. No programmable relay. Brand Victron Energy Manufacturer Part Number SHU050150050 Supply Voltage Range 6.5-70VDC Battery Capacity 1-9999Ah VE.Direct Communication Port Yes Protection Category IP21 Dimensions H46 x W120 x D54mm Warranty 5 Years

Read more less

Pre Cut Board 1220x800x18mm for mounting your installation on. Fire retardant MDF board

Read more less

Brand Victron Energy Manufacturer Part Number CHT000100000 Warranty 5 Years Country of Manufacture Netherlands

Read more less

The Energy Meter can be used to: Grid meter, and used as control input for an ESS System (1). Measure the output of a PV Inverter Measure the output of a AC Genset The meter is connected to the Color Control GX. There are two options in its wiring: Direct connection, either using the RS485 to USB interface with 1.8m cable length, or the 5.0m cable. Wireless connection via Zigbee Brand Victron Energy Manufacturer Part Number REL300300000 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number REC030001210 Warranty 5 Years

Read more less

FeaturesVE.Direct communication portThe VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed) Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage 210 – 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load and alarms         Proven reliabilityThe full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.High start-up powerNeeded to start loads such as power converters for LED lamps, halogen lamps or electric tools.ECO modeWhen in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.Remote on/offA remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector.DC connection with screw terminals No special tools needed for installation. 

Read more less

FeaturesVE.Direct communication portThe VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)   Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage 210 – 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load and alarms Proven reliabilityThe full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.High start-up powerNeeded to start loads such as power converters for LED lamps, halogen lamps or electric tools.ECO modeWhen in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.Remote on/offA remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector.DC connection with screw terminals No special tools needed for installation.

Read more less

The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG140301020R GTIN 8719076019107 Maximum Charge Current 140A Maximum Alternator Current 140A Number of Batteries 3 Alternator Energize Input Yes Connection M8 Studs Compensation Diode & Energize Connection 6.3mm Faston Dimensions H60 x W120 x D150mm Weight 1.1Kg Warranty 5 Years    

Read more less

The BatteryProtect is not designed for reverse currents from charging sources.   Features 12/24V auto ranging The BatteryProtect automatically detects system voltage. Programming made easy The BatteryProtect can be set to engage / disengage at several different voltages. The seven segment display will indicate which setting has been chosen. A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Ultra low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information. Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V. Ignition proof No relays but MOSFET switches, and therefore no sparks. Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage. Brand Victron Energy Manufacturer Part Number BPR000220400 Voltage 12/24 Peak Current (During 30 Seconds) 600A Max. Continuous Load Current 200A Connection M8 IP Rating Electronics: IP67 (potted) Connections: IP00 Dimensions (Including Terminals) H62 x W123 x D120mm Weight (kg) 0.8 Warranty 5 Years

Read more less

Brand Victron Energy Manufacturer Part Number CYR010120110R Voltage 12/24 LED Status Indication No Continuous Current 120 A Cranking Rating (5 seconds) 180 A Start Assist Yes (Cyrix remains engaged during 30 seconds) Protection Category IP54 Dimensions H46 x W46 x D80 Weight (kg) 0.11 Warranty 5 Years

Read more less

The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator.   Please see Victron Energy’s ‘Energy Unlimited’ or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely.   Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG160201020 Maximum Charge Current (A) 160 Maximum Alternator Current (A) 160 Number Of Batteries 2 Alternator Energize Input Yes Connection M8 Studs Compression didode & Energize connection 6.3mm Faston Dimensions H60 x W120 x D150mm Weight (kg) 1.1 Warranty 5 Years  

Read more less

Modular solar home system The SHS 200 is compatible with different size of batteries (up to 12V/160Ah) and solar panels (up to 200Wp). End-users can progressively increase their power subscription according to their needs and budget. With eleven DC load outputs, the SHS 200 can be connected to a variety of household appliances such LED lighting, phone charging, fans, TVs and a fridge. This solution is also powerful enough for entrepreneurial customers to run a small business. PAYGo ready The SHS 200 is primarily designed for Pay-as-you-go (PAYGo) operations. It is compatible with various PAYGo software platforms and includes a keypad for offline activation. How does it work? PAYGo operators usually offer solar home systems to their customers through a rent-to-own plan on prepayments. Customers can get a SHS 200 against a deposit. Then they make regular payments by mobile money over few months or years to finally own the unit. A recharge code is sent to their cell phone by SMS after each payment. The SHS 200 becomes active only when the code is pressed on its keypad. PAYGo operators can achieve profitability while off-grid populations afford reliable and clean energy. MPPT charger and smart battery management By using Maximum Power Point Tracking (MPPT) technology, the SHS 200 ensures that every drop of available power is rinsed out of the panels and harvested for storage. Additionally smart multi-stage charging and load disconnect features maintain the health and extends the life of the battery. The SHS 200 is compatible with lead-acid and lithium battery technologies.   Brand Victron Energy Remote activation Unlock codes sent to end-user via SMS to activate the system Warranty 5 Years Weight 0.39Kg Dimensions H148 x W204 x D67mm Protection Category IP41 Compatible PAYGo platforms PaygOps, Angaza, Paygee Compatible battery technologies Sealed lead-acid, Victron SuperPack (lithium) Temperature compensation Yes (automatic) Manufacturer Part Number SHS121409230 Suitable battery capacity Up to 160Ah Peak efficiency 96% Maximum charge / discharge currents 14A/20A Nominal PV power 50 to 200Wp total (36 cells panels) gtin 8719076050827 Country of Manufacture China

Read more less

The Phoenix 24/250 VE.Direct inverter allows you to power domestic equipment – requiring 230V – using ‘leisure’ or ‘automotive’ batteries rated at 12V, 24V or 48V DC. This unit has the IEC plug. Features of the Phoenix Inverter 24/250 VE.Direct VE.Direct communication port The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed) Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage 210 – 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load and alarms Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The Phoenix Inverter 24/250 VE.Direct are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the Phoenix Inverter VE.Direct will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote on/off A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector. DC connection with screw terminals No special tools needed for installation. Monitor, operate & control your system VictronConnect lets you get live status information and configure your Phoenix Inverter 24/250 VE.Direct when connected to a VE.Direct Bluetooth Smart Dongle. The REC040010210R is the correct controller for the Phoenix Inverter VE.Directs. Not sure what size inverter you need, why not take a look at our guide to sizing an inverter.

Read more less

The Phoenix 24/250 VE.Direct inverter allows you to power domestic equipment – requiring 230V – using ‘leisure’ or ‘automotive’ batteries rated at 12V, 24V or 48V DC. This unit has the IEC plug. Features of the Phoenix Inverter 24/250 VE.Direct VE.Direct communication port The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed) Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage 210 – 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load and alarms Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The Phoenix Inverter 24/250 VE.Direct are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the Phoenix Inverter VE.Direct will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote on/off A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector. DC connection with screw terminals No special tools needed for installation. Monitor, operate & control your system VictronConnect lets you get live status information and configure your Phoenix Inverter 24/250 VE.Direct when connected to a VE.Direct Bluetooth Smart Dongle. The REC040010210R is the correct controller for the Phoenix Inverter VE.Directs. Not sure what size inverter you need, why not take a look at our guide to sizing an inverter. Brand Victron Energy Manufacturer Part Number PIN241251100 gtin 8.72E+12 Voltage 24V

Read more less

In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.   When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.   Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!   Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed.   Brand Victron Energy Manufacturer Part Number ARG100301020 Maximum Charge Current (A) 100 Maximum Alternator Current (A) 100 Number Of Batteries 3 Connection M8 Bolts Dimensions H65 x W120 x D200mm Weight (kg) 1.4 Warranty 5 Years

Read more less

  Sealed, waterproof, multi-functional junction box gives high level of safety. High performance bypass diodes minimize the power drop caused by shade. Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation. A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems. Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance. High power models with pre-wired quick-connect system with MC4 (PV-ST01) connectors.

Read more less

The SmartShunt is a good alternative for a BMV battery monitor especially for systems where battery monitoring is needed but less wiring and clutter is wanted.The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor. Differences compared to BMV-712 Battery Monitor– No programmable visual and audible alarm– No programmable relay Why should I monitor my battery with the SmartShunt IP65 500A?Batteries are used in a wide variety of applications, mostly to store energy for later use. But how much energy is stored in the battery? No one can tell by just looking at it. The service life of batteries depends on many factors. Battery life may be shortened by under-charging, over-charging, excessively deep discharges, excessive charge or discharge currents, and by high ambient temperature. Monitoring the battery with a battery monitor will give important feedback to the user so that remedial measures can be taken when necessary. Doing this will extend battery life and the battery monitor will quickly pay for itself. Brand Victron Energy Manufacturer Part Number SHU065150050 gtin 8719076057895 Protection Category IP65 Bluetooth Enabled Yes Dimensions H46 x W120 x D54mm Warranty 5 Years Country of Manufacture India

Read more less

Secondly it can work as a Voltage- and Temperature-sense device for the inverter/charger. This works with all models, and is especially useful in combination with the MultiPlus-II, as it does not have on-board terminals for Voltage- and Temperature sense wiring For monitoring, the device is a great alternative in caravans, smaller yachts and motor homes for which the Color Control GX or Venus GX are a step too far Brand Victron Energy Manufacturer Part Number ASS030537010 Warranty 5 Years

Read more less

Tank levels can be read-out locally in the system. The GX Tank is compatible with current senders (4 to 20 mA) as well as voltage senders (0 to 10 V). The connection to the GX Device is via USB, which is also how the GX Tank is powered: no additional power wires required. Tank sender wiring is kept as simple as possible: two of the four inputs provide a 24 V power supply, to power the sender. The other two channels do require an external power supply, and there is a power in terminal together with fused outputs to facilitate that. Upper and lower limits are configurable, to allow using senders that provide only part of the scale, for example 0 to 5 V. To provide a stable reading, the readings are averaged damping. The damping can be configured between 1 and 60 seconds. Faulty sensors and wiring issues are detected: an alarm will be raised when values are out of range. For marine applications, the GX Device can transmit these tank levels on the NMEA 2000 network to be picked up by other displays such as an MFD.

Read more less

All models with adjustable output can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.   All models with adjustable output can be paralleled to increase output current Up to five units can be connected in parallel.   Easy to install Delivery includes four Insulated Fastons Female Crimp 6.3mm (eight Fastons in case of the Orion 24/12-40).   Low power models: please see Orion-Tr series Brand Victron Energy Manufacturer Part Number ORI241240021 GTIN 8719076038726 Voltage 24/12V Cont. Output Current 40A Protection Category IP20 Efficiency 95% Bluetooth Enabled No Dimensions H65 x W88 x D185mm Weight 0.85Kg Warranty 5 Years Country of Manufacture India

Read more less

In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.   When using ARGO FET Battery Isolators, there is no need to also increase the output voltage of the alternator. Care should taken however to keep cable lengths short and of sufficient cross section.   Example: When a current of 100 A flows through a cable of 50 mm2 cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly a current of 50 A through a cable of 10 mm2 cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 Volt!   Alternator energize input  Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Brand Victron Energy Manufacturer Part Number ARG100201020R GTIN 8719076019022 Maximum charge current 100A Maximum alternator current 100A Number Of Batteries 2 Connection M8 Bolts Dimensions H65 x W120 x D200mm Weight 1.4Kg Warranty 5 Years

Read more less